Fire Rated Cable

DESCRIPTION

Certified by LPCB to meet fire test Standards – BS EN 50200:2006 + Annex E 30 minutes, BS EN 50200 PH30, PH60 & PH120 & BS 6387 CWZ. It is also fully approved to the Low Smoke & Zero Halogen requirements detailed by BS 5839-:2013 & BS7629-1:2008.

Shield ‘Premium’ Cable retains continuity for 30 minutes under fire conditions at 830°C, this demanding fire cable test includes a final 15 minutes under fire & water spray conditions while a mechanical shock is applied every 5 minutes throughout the full 30 minute test.

Catalogue

SPECIFICATION

LPCB approved toFire Resistance StandardBS EN 50200:2006 +Annex E 30 mins
Fire Resistance StandardBS EN 50200:2006 PH120
Fire Resistance StandardBS 6387:1994 Clause 11 CWZ
Halogen Emission StandardBS EN 50267-2-1:1999
Halogen Emission StandardBS EN 61034-2:2005
Also for use withEmergency LightingBS 5266-1:2005
Voice Alarm Systems StandardBS 5839-8:2008
Voice Communication StandardBS 5839-9:2003
(Risk Assessment May Demand Mechanical Protection)
MaterialsDrain Wire0.80mm Dia (0.50mm2) Tinned Copper
ConductorsPlain Annealed Copper
Core InstallationFire Resistant ZHLS Silicone
ScreeningAluminium Foil
Outer SheathLow Smoke Halogen Free Thermoplastic
Working VoltageCore to Core500V
Core to CPC300V
TypesOuter Sheath ColoursRed, White or Black
Number of Cores2, 3 & 4 Core
Inner Cores CSA1.0, 1.5, 2.5 & 4.0mm CSA
Resistance1.0mm CSA18.1 Ohms / 1 Km
1.5mm CSA12.1 Ohms / 1 Km
2.5mm CSA7.41 Ohms / 1 Km
4.0mm CSA4.61 Ohms / 1 Km
Minimum Bend RadiusRadius = 6 x Diameter
Operating Temp.Minimum/Maximum-40°C to +90°C
Installation Temp.Minimum/Maximum0°C to +70°C
Voltage Drop
(DC or Single Phase AC)
1.0mm CSA44 Ohms mV / A / m
1.5mm CSA29 Ohms mV / A / m
2.5mm CSA18 Ohms mV / A / m
Approximate
Overall Diameter
2 Core1.0mm / 7.15mm
1.5mm / 7.40mm
2.5mm / 8.70mm
3 Core1.0mm / 7.75mm
1.5mm / 8.55mm
2.5mm / 9.20mm
4 Core1.0mm / 8.00mm
1.5mm / 8.80mm
2.5mm / 11.10mm
Approximate
Weights
2 Core with CPC1.0mm – 8.0 Kg / 100 m
1.5mm – 9.5 Kg / 100 m
2.5mm – 14.1 Kg / 100 m
3 Core with CPC1.0mm – 9.5 Kg / 100 m
1.5mm – 12.9 Kg / 100 m
2.5mm – 19.1 Kg / 100 m
4 Core with CPC1.0mm – 10.9 Kg / 100 m
1.5mm – 14.5 Kg / 100 m
2.5mm – 22.2 Kg / 100 m
Current Rating
(Current Ratings listed are at 30°C
Refer to BS7671/EE Wiring
Regulations for de-rating factor.)
Cable Clipped
(DC or Single Phase AC)
1.0mm 15A
1.5mm 19.5A
2.5mm 27A
Enclosed
(DC or Single Phase AC)
1.0mm 13A
1.5mm 16.5A
2.5mm 23A
Insulation Resistance10MÙ> at 5000V d.c.

FEATURES

  • Reduced Installation time and costs
  • Easy to install and Superb Working Flexibility
  • All in one – Easy to Strip Outer Sheath
  • No Separate Foil
  • No Additional Fibre Wraps
  • No mica tape on conductors
  • No additional core separators to remove
  • Cable Construction Provides High Level Data Protection

Open-Area Sounder Beacon

DESCRIPTION

SHIELD UL Open-Area Sounder Beacon makes full use of the protocol and has been designed for use in indoor, outdoor and open-areas. When the fire system is being commissioned, a Magnetic Wandcan be used to adjust and test each sounder locally.

FEATURES

  • 15 tone pairs
  • Sounder and beacon are independently configurable
  • Volume and tone settings are independently selectable from the control panel
  • Tones can be used for other purposes in addition to warning of fire, making the device ideal for use in schools etc.
  • Soft start option, ideal for hospitals and nursing homes
  • Group and global control for increased response time

Reflective Beam Detector

DESCRIPTION

The system comprises of a single unit incorporating an infra-red transmitter and receiver. The signal generated in the transmitter element and reflected by the prism back to the receiver element is analyzed for the presence of smoke. The internal microprocessor determines an alarm condition when a predetermined level is reached.

The system is designed to be mounted so the beam will project between 0.5 m and 0.6 m below and parallel to the ceiling. Lateral detection may be up to 9.144m on either side of the beam, providing a maximum total coverage area of up to 19,800 square feet (18.29 m x 100 m).

SPECIFICATION

Operating Range5 – 120 m
Operating Voltage Range12 to 36 VDC ±10%
Operating Controller Current
(with 1 or 2 Receivers)
14 mA (constant)
Operating Transmitter Current8 mA (per Transmitter)
Power Down Reset Time>20 seconds
Fire and Fault Relay ContactsResistive VFCO 2A @ 30 VDC
Operating Temp. (non-condensing)-20°C to +55°C
Optical Wavelength850 nm
IP RatingIP54
Relative Humidity (non-condensing)93%
Dimension (W x H x L) & Weight
Control Unit203 mm x 124 mm x 71 mm, 600 g
Transmitter & Receiver78 mm x 77 mm x 161 mm, 200 g

FEATURES

  • Easy set up and alignment
  • Single compact housing
  • Calibrated obscuration test filter included
  • Microprocessor controlled
  • Alarm latching or auto reset
  • Automatic gain control
  • 12 V DC or 24 V DC operation
  • Separate alarm and trouble contacts
  • Remote Test Station available

Auto Align Beam Detector

DESCRIPTION

The Alpha 5000 System is an auto-aligning, self-correcting infrared beam smoke detector. Up to 2 detector heads can report to a single ground level controller. In addition, each system controller houses two pairs of fire and trouble relays, one per detector. Once the detector head is installed, using the easyfit mounting system an integral LASER can be activated. This allows the reflective prism to be located quickly and with confidence.

SPECIFICATION

Primary Input Power14 to 36 V DC
Standby Current
(Depending On Number Of Detector Heads)
Low Current : 5 mA to 8.5 mA @ 24 V DC
High Current : 37 mA @ 24 V DC
Alarm Current5 mA to 8.5 mA @ 24 V DC depending on number of detector heads used
Relay Contacts1 A @ 30 V DC Resistive
Reset Time5 seconds maximum
Start Up Time45 seconds
Optical Wavelength850 nm
Temperature Rating UL Listed0°C to 38°C
Primary Input Power14 to 36 V DC
IP RatingIP54
Dimension (W x H x L) & Weight
Head134 mm x 134 mm x 131 mm, 1470 g
Controller202 mm x 87 mm x 230 mm, 1470 g
Prism100 mm x 9.5 mm x 105 mm

FEATURES

  • Up to 2 Detector Heads reporting to One Ground Level Controller
  • Built in Laser assisted prism mounting
  • Auto-Alignment 2 to 4 minutes per head
  • AutOptimise: Auto-Correction due to building shift
  • Built-in electronic UL/ULC obscuration-acceptance fire test
  • Contamination compensation
  • Separate Trouble and Alarm relays for each of the 2 channels
  • Password protected settings
  • Programmable alarm thresholds: 10% – 60% in 1% increments
  • Programmable Fault and Alarm delay: 2-30 Seconds

End to End Beam Detector

DESCRIPTION

The SHIELD Alpha 3000 End to End infrared Optical Beam Smoke Detector (OBSD) has been designed using the latest optical technology, incorporating modern industrial, electronic and software techniques. This detector offers cost effective protection of large, open area spaces with high ceilings. It is also very suited to applications where access to ceiling mounted smoke detectors presents practical difficulties.

The SHIELD Alpha 3000 is ideal for applications where line of sight for the IR (infra-red) detection path is narrow and where the building structure uses reflective surfaces. It has also been designed to be aesthetically pleasing and thus can equally suit modern architectural buildings as well as historical sites, particularly where ornate ceilings exist.

SPECIFICATION

Operating Range5 – 120 m
Operating Voltage Range12 to 36 VDC ±10%
Operating Controller Current
(with 1 or 2 Receivers)
14 mA (constant)
Operating Transmitter Current8 mA (per Transmitter)
Power Down Reset Time>20 seconds
Fire and Fault Relay ContactsResistive VFCO 2A @ 30 VDC
Operating Temp. (non-condensing)-20°C to +55°C
Optical Wavelength850 nm
IP RatingIP54
Relative Humidity (non-condensing)93%
Dimension (W x H x L) & Weight
Control Unit203 mm x 124 mm x 71 mm, 600 g
Transmitter & Receiver78 mm x 77 mm x 161 mm, 200 g

FEATURES

  • Separate Transmitter and Receiver Heads
  • Range 5 m to 120 m, configurable per set of Detectors
  • Lateral Spacing per NFPA 72 is 18 m
  • Integral Laser Alignment in Receiver
  • 2-wire Interface between Controller and Receiver
  • Single and Twin Channel capability
  • Separate Fire and Fault Relays per Detector
  • Low Level Controller with LCD display
  • Programmable Sensitivity and Fire Threshold
  • Automatic Gain Control (AGC) for drift compensation
  • Built-in electronic UL/ULC obscuration-acceptance fire test
  • Knockouts for ease of installation and wiring
  • Optional Transmitter powering from Controller

Repeater Panel

DESCRIPTION

Designed and manufactured to the highest standards in a quality controlled environment the SHIELD Omega-R fire alarm reporter provides a simple and convenient method of extending thecontrols and indications of the SHIELD Omega fire alarm control panel to other locations.

The large, graphic liquid crystal display and high brightness LED indicators duplicate the indications on the SHIELD Omega fire alarm control panel at up to 15 additional locations via a simple, two-wire serial data connection.

The SHIELD Omega-R is powered by 24V DC (which can be via an additional 2 conductors from the control panel or local 24V DC listed supply).

SHIELD Omega-R is housed in a small enclosure which is styled similarly to the SHIELD Omega control panel and is ideal for installations where a large control panel would be detrimental décor such as entrance halls.

Up to 15 SHIELD Omega-R annunciators can be connected to each control panel on the Omega network making Omega-R ideal where multiple points of indication and/or control are required such as nurses stations or shop units.

FEATURES

  • Available in Red
  • Up to 15 annunciators can be connected to each SHIELD Omega fire control panel
  • Large liquid crystal display (240×64 pixels)
  • High brightness LED indications
  • Internal sounder
  • Replicates all panel controls
  • Simple, two-wire serial connection
  • Small, style enclosure
  • Removable electronics for easy installation
  • 24V DC powered
  • Low power consumption
  • Multi language options
  • Connection supervised by SHIELD Omega fire control panel

Analog Control Panel (2 or 4 Loops)

DESCRIPTION

Designed and manufactured to the highest standards in a quality controlled environment the SHIELD Omega-R fire alarm reporter provides a simple and convenient method of extending thecontrols and indications of the SHIELD Omega fire alarm control panel to other locations.

FEATURES

  • Available in Red
  • Up to 15 annunciators can be connected to each SHIELD Omega fire control panel
  • Large liquid crystal display (240×64 pixels)
  • High brightness LED indications
  • Internal sounder
  • Replicates all panel controls
  • Simple, two-wire serial connection
  • Small, style enclosure
  • Removable electronics for easy installation
  • 24V DC powered
  • Low power consumption
  • Multi language options
  • Connection supervised by SHIELD Omega fire control panel

Analog Control Panel (1 or 2 Loops)

DESCRIPTION
The SA-P20R and SA-P4LR analog addressable FACP supports 2 or 4 SLC loops for a total of 500 primary points or 800 points using subpoints. SLC loop communications uses standard twisted pair cabling, shielded cable is not necessary.
The panel may be configured with various communication cards; Communications options support central station monitoring, Virtual Panel, and networking.
The Panel can be configured as a stand alone panel with just a few devices for a small building, it can also operate as the building system and can be part of a network with a total of 64 nodes serving a multiple building campus or a very large facility.
Auto Learn capability provides a convenient method to troubleshoot new installations before final programming is loaded

FEATURES

  • UL 864 9th Edition listed
  • Multi-Loop 2 Analog Addressable
  • Loops Field upgradable to 4
  • 126 primary points per loop
  • Powerful, network wide cause and effects (500 total). Fully user programmable by point or zone
  • 800 points per panel when using devices with sub-points
  • Up to 10,000 ft. wiring length on SLC loop
  • 64 Panels on a network
  • Programmable through a PC connection to the panel, or through keypad
  • Programmable relays – 5
  • Supervised Powered Outputs – 3
  • Programmable notification appliance circuits:4
  • Power per NAC: 1.6 Amps Max
  • Programmable outputs on SLC loop
  • Programmable Function button on front display
  • Fire Drill button on front display
  • Day and night sensitivity settings (user programmable)
  • Power Supply: 5.25 Amp, regulated & integrated
  • LCD Display: 8×40
  • Zonal Mode: Annunciation by zone w/o individual relationships
  • Panel Ring Modes: Common, Zonal, and Stage 2
  • NAC Outputs programmable as Continuous, March, Temporal
  • Program cause and effects AND, OR, or any two (Cross Zone)
  • Battery size: Up to 17 Ah in standard enclosure; up to 52 Ah with external cabinet
  • Access levels: 3
  • Access key switch: Yes
  • Recognized for use in High Rise
  • One-man walk test – Fire Test Mode
  • Available in Red
Fire Alarm & Detection System - UL Listed - Omega Series> Product

    array(9) { ["_vc_post_settings"]=> array(13) { [0]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [1]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [2]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [3]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [4]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [5]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [6]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [7]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [8]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [9]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [10]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [11]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" [12]=> string(30) "a:1:{s:10:"vc_grid_id";a:0:{}}" } ["slide_template"]=> array(1) { [0]=> string(7) "default" } ["_wpb_vc_js_status"]=> array(1) { [0]=> string(4) "true" } ["_custom_page_options"]=> array(18) { [0]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [1]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [2]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [3]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [4]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [5]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [6]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [7]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [8]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [9]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [10]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [11]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [12]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [13]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [14]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [15]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [16]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" [17]=> string(32) "a:1:{s:7:"sidebar";s:5:"right";}" } ["_wp_old_slug"]=> array(3) { [0]=> string(35) "balance-pressure-proportioning-skid" [1]=> string(31) "low-expansion-foam-branch-pipes" [2]=> string(29) "high-expansion-foam-generator" } ["_dp_original"]=> array(1) { [0]=> string(4) "1275" } ["_edit_lock"]=> array(1) { [0]=> string(12) "1538109890:1" } ["_edit_last"]=> array(1) { [0]=> string(1) "1" } ["_thumbnail_id"]=> array(1) { [0]=> string(4) "1415" } }